Last Geo-info is last time position information. Now is LBS position information.
LAC: Location Area Code
MCC:Mobile Country Code
MNC:Mobile Network Code
By these LBS information, police can find the position.
5.8 Get absolute street address
5.8.1 You must register our server if want to use this function,If you want the SMS reply with local language,please use local telecom mobile operator sim card.
5.8.2 send:” address+password” to device, it will reply SMS including absolute street address. For example:Block 13,28 Cheung Sha Wan Road,Kowloon,Hongkong.
5.9 Auto Track
5.9.1 Send SMS command “t030s005n+password” to the tracker device, it will report the Geo-info at 30s intervals for 5 times. (s:second, m:minute, h:hour). This command setting must be in 3 digits.
5.9.2 Unlimited times auto track: Send SMS “t030s***n+password” to the tracker device, it will reply the Geo-info continuously at 30 seconds intervals.
5.9.3 Cancellation: Send SMS “notn+password” to the tracker device.
Note: the interval must not less than 20s.
5.10 Location based service (LBS)
When the tracker device doesn’t received valid GPS signals, tracker will locate by LBS.
5.11 Monitor (Voice Surveillance)
5.11.1 The command to switch between Track and Monitor are “tracker” and “ monitor”.
5.11.2 The default mode is “track” (Track mode).
5.11.3 Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode.
5.11.4 Send SMS “tracker+password” to the unit, it will reply “tracker ok!” and restore to “track” mode.
5.12.1 Auto Storage:When the tracker devices lost GSM signals or fall offline from GPRS, tracker will store the tracking position and alerts automatically in the flash upon the pre-set condition, when GSM signals get back, all the event alerts will be auto-sent to the authorized numbers or monitoring platform (server), but the stored tracking data should be loaded to the monitoring platform via SMS command.
5.12.2 Storage upon times: Send SMS: “save030s005n+password” to the tracker unit, it will reply “save ok”, and will store the lat, long locations every 30 seconds for 5 times. (S: second, m: minute; h: hour).
5.12.3 Multi-Storage:Send sms:”save030s***n+ password” to tracker device, it will reply “save ok”.
5.12.4: Storage Clearance: send SMS: “clear+ password” to tracker device, it will reply “clear ok”.
5.12.5 Storage Volume: external TF card support 32GB at most.
5.13 Data Load
5.13.1 Current date Load: Send SMS: “load+ password” to tracker device, it will reply: “load ok” if the device is working well under GPRS mode; if not, it will reply “load fail! Please check gprs” that means device does not work under GPRS mode.
5.13.2 Specified date Load; Send SMS: “load+ password+ space+ year month date” to tracker device, it will reply: “load ok” and load the tracking data to the monitoring platform upon the valid time you choose. For Example: send SMS: “load123456 20110425” to the tracker device, means to load the tracking data of 25th April 2011 to monitoring platform.
5.14 Shock sensor alarm
It is disabled as default, send “shock+password to tracker, tracker will reply “shock ok!”. “Sensor alarm+lat/long” will send to authorized phone number when tracker is being shocked, and one alarm for each shock event trigger.
Cancel: Send “noshock+password” to cancel the shock sensor alarm.
Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the district.
5.15.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS: “stockade+password+space+latitude,longitude; latitude,longitude” to unit to set the restricted district. In case of breach, it will send SMS “stockade!+geo-info” to the authorized numbers every 3 minutes.
Remark: The first latitude&longitude is coordinate of the top left corner of the Geo-fence, while the second latitude&longitude is the coordinate of the bottom right corner.
5.15.2 Cancel: Send SMS:” nostockade+password” to deactivate this function.
5.16 Movement alert
5.16.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS: “move+password” to the unit, then the unit will reply “move ok!”. In case of such a movement ( the unit default distance is 200M ), it will send SMS “Move+ Geo-info” to the authorized numbers every 3 minutes.
5.16.2 Cancel: Send SMS:” nomove+password” to deactivate the movement alert.
5.17 Overspeed alert:
5.17.1 Set up: Send SMS:” speed+password+space+080” to the unit (suppose the speed is 80km/h), and it will reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will send SMS :”speed+080!+Geo-info” to the authorized numbers every 3 minutes.
5.17.2 Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm.
Remark: The recommended speed should be not less than 50km/h. For below that rate, it will be effected the accuracy by gps signals drift etc.
5.18 SOS button
Press the SOS for 3 seconds, it will send “help me!+ Geo-info” to all the authorized numbers every 3 minutes. It will stop sending such a SMS when any authorized number reply SMS “help me!” to the tracker.
5.19 Low battery alert
When GPS device battery is going to be about 3.7V, it will send SMS:”low battery+Ge-info”
at 3 minutes interval. It will stop sending such a SMS when any authorized number reply SMS “low battery” to the tracker.
5.20 State Checking
Send SMS:”check+password” to the tracker device, it will reply the recent status via SMS as: GSM: 100% GPS: OK/NO GPRS: ON/OFF battery: 100%.
Remark: GPS NO, only mean there are no GPS position request.
5.21 IMEI checking:
Send SMS command “imei+password” to the unit. E.g.: Send SMS command “imei123456” to the unit, an IMEI number in 15 digits will be replied to your cell phone.
5.22 Terminal (local) Time Setting
5.22.1 Send SMS “time+space+zone+password+space+local time zone”.
For example, Send SMS “time zone123456 8” (time zone of China).
If the local time zone is negative as “-8”, then it should set as SMS:
“time zone123456 -8”.
5.23 GPRS setting
The device can auto set APN,the function support most countries,the default IP is our company IP.User can use SMS or our setting software set the parameter.
5.23.1 Setting up APN
184.108.40.206 APN standards for Access Point Name and differs from country to country. For more information about the local APN, inquire with your local GPRS network operator.
220.127.116.11 Text the tracker a SMS “APN+password + Space + your local APN+APN user name+apn password”.
If need no APN user,apn password,the SMS format is: “APN+password + Space + your local APN.for example:apn123456 cmnet claro claro,mean:local APN:cmnet,APN user:claro,APN password:claro.
If need not APN user,APN password:the format is:apn123456 cmnet.
5.23.2 The device support IP & Domain setting.
Example1:Send SMS command “adminip123456 222.111.555.77 9999” to the tracker device, If succeeded, “adminip OK” is returned by the device in SMS.( 123456 is default password,222.111.555.77 is IP,9999 is port, remark:this is a example, IP and port is not true).
Example2:Send SMS command “adminip123456 www.19gps.net 7018” to the tracker device, If succeeded, “adminip OK” is returned by the device in SMS.( 123456 is default password, www.19gps.net is our platform Domain,7018 is port, remark: for using our platform can set as this example).
5.24 Modes switch between “SMS” and “GPRS”
5.24.1 The default mode is “SMS”
5.24.2 Send SMS “GPRS+password” to the unit, and it will reply “GPRS ok!” and switch to “GPRS” mode.
5.24.3 Send SMS “SMS+password” to the unit, it will reply “SMS ok!” and restore to “SMS” mode.